19: l2tpeth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast master foo state UNKNOWN mode DEFAULT group default qlen 1000
    link/ether 7e:0a:f4:5c:ef:8c brd ff:ff:ff:ff:ff:ff
    alias L2 VPN Tunnel

master foo <- foo is the VRF name

May 6 2021, 7:08 PM · VyOS 1.3 Equuleus (1.3.0), VyOS 1.4 Sagitta

c-po moved T3523: VRF BGP daemon route-map command missing from Open to Finished on the VyOS 1.4 Sagitta board.

May 6 2021, 6:04 PM · VyOS 1.4 Sagitta

c-po moved T3520: Cannot add tunnel interface to isis within vrf from Open to Finished on the VyOS 1.4 Sagitta board.

May 6 2021, 6:04 PM · VyOS 1.4 Sagitta

c-po triaged T3523: VRF BGP daemon route-map command missing as Low priority.

May 6 2021, 5:30 PM · VyOS 1.4 Sagitta

c-po added a comment to T3523: VRF BGP daemon route-map command missing.

@Viacheslav it must be added in the proper order and contexts need to be entered - exited appropriately

May 6 2021, 5:30 PM · VyOS 1.4 Sagitta

c-po closed T3523: VRF BGP daemon route-map command missing as Resolved.

May 6 2021, 5:28 PM · VyOS 1.4 Sagitta

Viacheslav added a comment to T3523: VRF BGP daemon route-map command missing.

It seems a bug with frr-reload

!
router bgp 64500 vrf foo
 no bgp ebgp-requires-policy
 no bgp network import-check
 exit
!
vrf foo
 ip protocol bgp route-map RMAP
 exit-vrf
!
route-map RMAP permit 10
 set tag 555
!
line vty
!

May 6 2021, 5:13 PM · VyOS 1.4 Sagitta

c-po changed the status of T3523: VRF BGP daemon route-map command missing from Open to In progress.

May 6 2021, 5:06 PM · VyOS 1.4 Sagitta

Viacheslav added a comment to T3523: VRF BGP daemon route-map command missing.

Update I find an example

!
vrf foo
 ip protocol bgp route-map RMAP
 exit-vrf
!
router bgp 64500 vrf foo
 no bgp ebgp-requires-policy
 no bgp network import-check
!

May 6 2021, 4:03 PM · VyOS 1.4 Sagitta

Viacheslav added a comment to T3523: VRF BGP daemon route-map command missing.

@ernstjo
Is it supported by FRR?
Can you provide an example?

May 6 2021, 3:56 PM · VyOS 1.4 Sagitta

ernstjo created T3523: VRF BGP daemon route-map command missing.

May 6 2021, 12:59 PM · VyOS 1.4 Sagitta

erkin changed Is it a breaking change? from none to compatible on T3351: Installer checking MD5 checksums on the ISO image.

May 6 2021, 10:33 AM · VyOS 1.4 Sagitta

erkin triaged T3355: Remove all remaining legacy Vyatta code as Normal priority.

May 6 2021, 8:49 AM · VyOS Rolling

erkin changed the status of T3355: Remove all remaining legacy Vyatta code from Open to In progress.

May 6 2021, 7:55 AM · VyOS Rolling

erkin changed the status of T3351: Installer checking MD5 checksums on the ISO image from Open to In progress.

May 6 2021, 7:55 AM · VyOS 1.4 Sagitta

erkin changed the status of T936: Reimplementation of tech-support diagnostic file generation from In progress to On hold.

May 6 2021, 7:54 AM · test, VyOS 1.4 Sagitta

erkin changed the status of T936: Reimplementation of tech-support diagnostic file generation, a subtask of T3355: Remove all remaining legacy Vyatta code, from In progress to On hold.

May 6 2021, 7:54 AM · VyOS Rolling

erkin updated the task description for T3356: Script for remote file transfers.

May 6 2021, 6:36 AM · VyOS 1.3 Equuleus (1.3.0), VyOS 1.4 Sagitta

carl.byington created T3522: policy based routing not working.

May 6 2021, 1:50 AM · VyOS 1.4 Sagitta (1.4.0-epa1), Restricted Project

May 5 2021

c-po closed T3335: Some OSPFv3 show commands do not work as Resolved.

May 5 2021, 8:16 PM · VyOS 1.4 Sagitta

c-po closed T3520: Cannot add tunnel interface to isis within vrf as Resolved.

May 5 2021, 8:05 PM · VyOS 1.4 Sagitta

c-po changed the status of T3520: Cannot add tunnel interface to isis within vrf from Open to In progress.

May 5 2021, 7:53 PM · VyOS 1.4 Sagitta

c-po added a comment to T3520: Cannot add tunnel interface to isis within vrf.

Problem is because of LSP MTU missmatch

May 5 2021, 7:44 PM · VyOS 1.4 Sagitta

ernstjo added a comment to T3520: Cannot add tunnel interface to isis within vrf.

Maybe I found the issue:

May 5 2021, 7:13 PM · VyOS 1.4 Sagitta

c-po claimed T3520: Cannot add tunnel interface to isis within vrf.

May 5 2021, 6:45 PM · VyOS 1.4 Sagitta

ernstjo created T3520: Cannot add tunnel interface to isis within vrf.

May 5 2021, 3:21 PM · VyOS 1.4 Sagitta

Viacheslav added a comment to T3473: IPSec op-mode show sa error.

@rob it fixed in the latest 1.3 with commit https://github.com/vyos/vyos-1x/commit/c7430fbb8738d76e63a6972b7399fa39572e2254
probably just not hit at that time in 1.3-rc4

May 5 2021, 2:28 PM · VyOS 1.4 Sagitta

ernstjo created T3519: Cannot add / assign L2TPv3 to vrf.

May 5 2021, 2:10 PM · VyOS 1.3 Equuleus (1.3.0), VyOS 1.4 Sagitta

rob added a comment to T3473: IPSec op-mode show sa error.

this error also occure in VyOS 1.3 RC4.

May 5 2021, 12:42 PM · VyOS 1.4 Sagitta

hard added a comment to T3277: DNS Forwarding - reverse zones.

Implemented, wait for approval

May 5 2021, 10:57 AM · VyOS 1.3 Equuleus (1.3.0-epa2), VyOS 1.4 Sagitta

Viacheslav updated subscribers of T3518: Warning messages when using SCP commit-archive.

May 5 2021, 7:51 AM · VyOS 1.4 Sagitta

FileGo created T3518: Warning messages when using SCP commit-archive.

May 5 2021, 7:19 AM · VyOS 1.4 Sagitta

shyrwall added a comment to T3514: NIC flap at any interface change.

Don't think this is related to the i40e driver. I think it's because vyos sees

May 5 2021, 5:08 AM · VyOS 1.3 Equuleus (1.3.0), VyOS 1.4 Sagitta

shyrwall added a comment to T3514: NIC flap at any interface change.

vyos@vyos# set interfaces ethernet eth3 description Test
[edit]
vyos@vyos# commit
DEBUG/IFCONFIG cmd 'ip -json -detail link list dev eth3'
DEBUG/IFCONFIG returned (out):
[{"ifindex":5,"ifname":"eth3","flags":["BROADCAST","MULTICAST","UP","LOWER_UP"],"mtu":1500,"qdisc":"mq","operstate":"UP","linkmode":"DEFAULT ","group":"default","txqlen":1000,"link_type":"ether","address":"3c:fd:fe:dd:bd:89","broadcast":"ff:ff:ff:ff:ff:ff","promiscuity":0,"min_mtu ":68,"max_mtu":9702,"inet6_addr_gen_mode":"none","num_tx_queues":16,"num_rx_queues":16,"gso_max_size":65536,"gso_max_segs":65535,"phys_port_ id":"3cfdfeddbd89","vfinfo_list":[]}]
DEBUG/IFCONFIG cmd 'ip -json -detail link list dev eth3'
DEBUG/IFCONFIG returned (out):
[{"ifindex":5,"ifname":"eth3","flags":["BROADCAST","MULTICAST","UP","LOWER_UP"],"mtu":1500,"qdisc":"mq","operstate":"UP","linkmode":"DEFAULT ","group":"default","txqlen":1000,"link_type":"ether","address":"3c:fd:fe:dd:bd:89","broadcast":"ff:ff:ff:ff:ff:ff","promiscuity":0,"min_mtu ":68,"max_mtu":9702,"inet6_addr_gen_mode":"none","num_tx_queues":16,"num_rx_queues":16,"gso_max_size":65536,"gso_max_segs":65535,"phys_port_ id":"3cfdfeddbd89","vfinfo_list":[]}]
DEBUG/IFCONFIG cmd 'ethtool --show-pause eth3'
DEBUG/IFCONFIG returned (out):
Pause parameters for eth3:
Autonegotiate: off
RX: off
TX: off
DEBUG/IFCONFIG cmd 'ethtool --pause eth3 autoneg on tx on rx on'
could not set flowcontrol for eth3
DEBUG/IFCONFIG cmd 'ethtool -K eth3 gro off'
DEBUG/IFCONFIG cmd 'ethtool -K eth3 gso off'
DEBUG/IFCONFIG write '0' > '/sys/class/net/eth3/queues/rx-0/rps_cpus'
DEBUG/IFCONFIG cmd 'ethtool -K eth3 sg off'
DEBUG/IFCONFIG cmd 'ethtool -K eth3 tso off'
DEBUG/IFCONFIG cmd 'ethtool -K eth3 ufo off'
DEBUG/IFCONFIG cmd 'ethtool eth3'
DEBUG/IFCONFIG returned (out):
Settings for eth3:

Supported ports: [ FIBRE ]
Supported link modes:   1000baseX/Full
                        10000baseSR/Full
Supported pause frame use: Symmetric Receive-only
Supports auto-negotiation: Yes
Supported FEC modes: Not reported
Advertised link modes:  1000baseX/Full
                        10000baseSR/Full
Advertised pause frame use: No
Advertised auto-negotiation: Yes
Advertised FEC modes: Not reported
Speed: 10000Mb/s
Duplex: Full
Port: FIBRE
PHYAD: 0
Transceiver: internal
Auto-negotiation: off
Supports Wake-on: d
Wake-on: d
Current message level: 0x00000007 (7)
                       drv probe link
Link detected: yes

DEBUG/IFCONFIG cmd 'ethtool -s eth3 autoneg on'
{'description': 'Test',
'duplex': 'auto',
'ifname': 'eth3',
'ip': {'arp_cache_timeout': '30'},
'mtu': '1500',
'speed': 'auto',
'vif': {'80': {'address': ['1.3.3.7/29'],

'ip': {'arp_cache_timeout': '30'},
'mtu': '1500'}}}

DEBUG/IFCONFIG cmd 'ip link set dev eth3 alias "Test"'
DEBUG/IFCONFIG write '1' > '/proc/sys/net/ipv4/conf/eth3/link_filter'
DEBUG/IFCONFIG cmd 'sudo systemctl stop [email protected]'
DEBUG/IFCONFIG cmd 'sudo systemctl stop [email protected]'
DEBUG/IFCONFIG cmd 'ip -json -detail link list dev eth3'
DEBUG/IFCONFIG returned (out):
[{"ifindex":5,"ifname":"eth3","flags":["NO-CARRIER","BROADCAST","MULTICAST","UP"],"mtu":1500,"qdisc":"mq","operstate":"DOWN","linkmode":"DEF AULT","group":"default","txqlen":1000,"link_type":"ether","address":"3c:fd:fe:dd:bd:89","broadcast":"ff:ff:ff:ff:ff:ff","promiscuity":0,"min _mtu":68,"max_mtu":9702,"inet6_addr_gen_mode":"none","num_tx_queues":16,"num_rx_queues":16,"gso_max_size":65536,"gso_max_segs":65535,"phys_p ort_id":"3cfdfeddbd89","ifalias":"Test","vfinfo_list":[]}]
DEBUG/IFCONFIG cmd 'ip link set dev eth3 nomaster'
DEBUG/IFCONFIG write '30000' > '/proc/sys/net/ipv4/neigh/eth3/base_reachable_time_ms'
DEBUG/IFCONFIG write '1' > '/proc/sys/net/ipv4/conf/eth3/arp_filter'
DEBUG/IFCONFIG write '0' > '/proc/sys/net/ipv4/conf/eth3/arp_accept'
DEBUG/IFCONFIG write '0' > '/proc/sys/net/ipv4/conf/eth3/arp_announce'
DEBUG/IFCONFIG write '0' > '/proc/sys/net/ipv4/conf/eth3/arp_ignore'
DEBUG/IFCONFIG write '0' > '/proc/sys/net/ipv4/conf/eth3/proxy_arp'
DEBUG/IFCONFIG write '0' > '/proc/sys/net/ipv4/conf/eth3/proxy_arp_pvlan'
DEBUG/IFCONFIG write '1' > '/proc/sys/net/ipv4/conf/eth3/forwarding'
DEBUG/IFCONFIG write '0' > '/proc/sys/net/ipv4/conf/eth3/rp_filter'
DEBUG/IFCONFIG write '1' > '/proc/sys/net/ipv6/conf/eth3/forwarding'
DEBUG/IFCONFIG write '1' > '/proc/sys/net/ipv6/conf/eth3/accept_ra'
DEBUG/IFCONFIG write '0' > '/proc/sys/net/ipv6/conf/eth3/autoconf'
DEBUG/IFCONFIG write '1' > '/proc/sys/net/ipv6/conf/eth3/dad_transmits'
DEBUG/IFCONFIG cmd 'ip link set dev eth3 mtu 1500'
DEBUG/IFCONFIG cmd 'ip -json -detail link list dev eth3'
DEBUG/IFCONFIG returned (out):
[{"ifindex":5,"ifname":"eth3","flags":["NO-CARRIER","BROADCAST","MULTICAST","UP"],"mtu":1500,"qdisc":"mq","operstate":"DOWN","linkmode":"DEF AULT","group":"default","txqlen":1000,"link_type":"ether","address":"3c:fd:fe:dd:bd:89","broadcast":"ff:ff:ff:ff:ff:ff","promiscuity":0,"min _mtu":68,"max_mtu":9702,"inet6_addr_gen_mode":"none","num_tx_queues":16,"num_rx_queues":16,"gso_max_size":65536,"gso_max_segs":65535,"phys_p ort_id":"3cfdfeddbd89","ifalias":"Test","vfinfo_list":[]}]
DEBUG/IFCONFIG cmd 'xdp_loader -d eth3 -U --auto-mode'
DEBUG/IFCONFIG returned (out):
INFO: xdp_link_detach() no curr XDP prog on ifindex:5
DEBUG/IFCONFIG cmd 'tc qdisc del dev eth3 handle ffff: ingress 2> /dev/null;tc qdisc del dev eth3 handle 1: root prio 2> /dev/null;set $?=0'
DEBUG/IFCONFIG cmd 'ip link set dev eth3 up'
{'address': ['1.3.3.7/29'],
'ifname': 'eth3.80',
'ip': {'arp_cache_timeout': '30'},
'mtu': '1500'}
DEBUG/IFCONFIG cmd 'ip link set dev eth3.80 alias ""'
DEBUG/IFCONFIG write '1' > '/proc/sys/net/ipv4/conf/eth3.80/link_filter'
DEBUG/IFCONFIG cmd 'sudo systemctl stop [email protected]'
DEBUG/IFCONFIG cmd 'sudo systemctl stop [email protected]'
DEBUG/IFCONFIG cmd 'ip -json -detail link list dev eth3.80'
DEBUG/IFCONFIG returned (out):
[{"ifindex":8,"link":"eth3","ifname":"eth3.80","flags":["NO-CARRIER","BROADCAST","MULTICAST","UP"],"mtu":1500,"qdisc":"noqueue","operstate": "LOWERLAYERDOWN","linkmode":"DEFAULT","group":"default","txqlen":1000,"link_type":"ether","address":"3c:fd:fe:dd:bd:89","broadcast":"ff:ff:f f:ff:ff:ff","promiscuity":0,"min_mtu":0,"max_mtu":65535,"linkinfo":{"info_kind":"vlan","info_data":{"protocol":"802.1Q","id":80,"flags":["RE ORDER_HDR"]}},"inet6_addr_gen_mode":"none","num_tx_queues":1,"num_rx_queues":1,"gso_max_size":65536,"gso_max_segs":65535}]
DEBUG/IFCONFIG cmd 'ip link set dev eth3.80 nomaster'
DEBUG/IFCONFIG write '30000' > '/proc/sys/net/ipv4/neigh/eth3.80/base_reachable_time_ms'
DEBUG/IFCONFIG write '1' > '/proc/sys/net/ipv4/conf/eth3.80/arp_filter'
DEBUG/IFCONFIG write '0' > '/proc/sys/net/ipv4/conf/eth3.80/arp_accept'
DEBUG/IFCONFIG write '0' > '/proc/sys/net/ipv4/conf/eth3.80/arp_announce'
DEBUG/IFCONFIG write '0' > '/proc/sys/net/ipv4/conf/eth3.80/arp_ignore'
DEBUG/IFCONFIG write '0' > '/proc/sys/net/ipv4/conf/eth3.80/proxy_arp'
DEBUG/IFCONFIG write '0' > '/proc/sys/net/ipv4/conf/eth3.80/proxy_arp_pvlan'
DEBUG/IFCONFIG write '1' > '/proc/sys/net/ipv4/conf/eth3.80/forwarding'
DEBUG/IFCONFIG write '0' > '/proc/sys/net/ipv4/conf/eth3.80/rp_filter'
DEBUG/IFCONFIG write '1' > '/proc/sys/net/ipv6/conf/eth3.80/forwarding'
DEBUG/IFCONFIG write '1' > '/proc/sys/net/ipv6/conf/eth3.80/accept_ra'
DEBUG/IFCONFIG write '0' > '/proc/sys/net/ipv6/conf/eth3.80/autoconf'
DEBUG/IFCONFIG write '1' > '/proc/sys/net/ipv6/conf/eth3.80/dad_transmits'
DEBUG/IFCONFIG cmd 'ip link set dev eth3.80 mtu 1500'
DEBUG/IFCONFIG cmd 'ip -json -detail link list dev eth3.80'
DEBUG/IFCONFIG returned (out):
[{"ifindex":8,"link":"eth3","ifname":"eth3.80","flags":["NO-CARRIER","BROADCAST","MULTICAST","UP"],"mtu":1500,"qdisc":"noqueue","operstate": "LOWERLAYERDOWN","linkmode":"DEFAULT","group":"default","txqlen":1000,"link_type":"ether","address":"3c:fd:fe:dd:bd:89","broadcast":"ff:ff:f f:ff:ff:ff","promiscuity":0,"min_mtu":0,"max_mtu":65535,"linkinfo":{"info_kind":"vlan","info_data":{"protocol":"802.1Q","id":80,"flags":["RE ORDER_HDR"]}},"inet6_addr_gen_mode":"none","num_tx_queues":1,"num_rx_queues":1,"gso_max_size":65536,"gso_max_segs":65535}]
DEBUG/IFCONFIG cmd 'xdp_loader -d eth3.80 -U --auto-mode'
DEBUG/IFCONFIG returned (out):
INFO: xdp_link_detach() no curr XDP prog on ifindex:8
DEBUG/IFCONFIG cmd 'ip link set dev eth3.80 up'

May 5 2021, 5:03 AM · VyOS 1.3 Equuleus (1.3.0), VyOS 1.4 Sagitta

May 4 2021

c-po closed T3504: BGP Per Peer Graceful Restart as Resolved.

May 4 2021, 9:02 PM · VyOS 1.4 Sagitta

Viacheslav updated the task description for T3517: FRR 7.5 bfd behavior for 1.3.

May 4 2021, 7:51 PM · VyOS 1.3 Equuleus (1.3.0)

Viacheslav created T3517: FRR 7.5 bfd behavior for 1.3.

May 4 2021, 7:51 PM · VyOS 1.3 Equuleus (1.3.0)

c-po changed the status of T3514: NIC flap at any interface change from In progress to On hold.

May 4 2021, 7:06 PM · VyOS 1.3 Equuleus (1.3.0), VyOS 1.4 Sagitta

c-po added a comment to T3514: NIC flap at any interface change.

I have boiled down your commands to the following:

May 4 2021, 6:41 PM · VyOS 1.3 Equuleus (1.3.0), VyOS 1.4 Sagitta

c-po changed the status of T3514: NIC flap at any interface change from Open to In progress.

May 4 2021, 5:56 PM · VyOS 1.3 Equuleus (1.3.0), VyOS 1.4 Sagitta

shyrwall added a comment to T3514: NIC flap at any interface change.

set interfaces ethernet eth0 hw-id 'ac:1f:6b:76:95:98'
set interfaces ethernet eth1 hw-id 'ac:1f:6b:76:95:99'
set interfaces ethernet eth2 hw-id 'ac:1f:6b:76:98:7a'
set interfaces ethernet eth3 hw-id 'ac:1f:6b:76:98:7b'
set interfaces ethernet eth4 hw-id '3c:fd:fe:dd:bd:88'
set interfaces ethernet eth5 hw-id '3c:fd:fe:dd:bd:89'
set interfaces ethernet eth5 vif 58 address 'x.x.x.x'
set interfaces ethernet eth5 vif 80 address 'x.x.x.x'
set interfaces ethernet eth5 vif 80 ip ospf cost '500'
set interfaces ethernet eth5 vif 80 ip ospf dead-interval '30'
set interfaces ethernet eth5 vif 81 address 'x.x.x.x'
set interfaces ethernet eth5 vif 81 ip ospf cost '1'
set interfaces ethernet eth5 vif 81 ip ospf dead-interval '30'
set interfaces ethernet eth5 vif 81 ip ospf network 'point-to-point'

May 4 2021, 2:49 PM · VyOS 1.3 Equuleus (1.3.0), VyOS 1.4 Sagitta

shyrwall created T3514: NIC flap at any interface change.

May 4 2021, 9:33 AM · VyOS 1.3 Equuleus (1.3.0), VyOS 1.4 Sagitta

May 2 2021

Unknown Object (User) added a comment to T3480: Does not possible to change console baud-rate.

Hi @hard, I think behavior should be another for VM. Did you try to change speed when you connected via serial?

May 2 2021, 5:37 PM · VyOS 1.4 Sagitta

c-po closed T3510: RADIUS usersname is not shown on CLI as Resolved.

May 2 2021, 4:31 PM · VyOS 1.4 Sagitta

c-po closed T3511: Update libnss-mapuser and libpam-radius packages from CUMULUS Linux, a subtask of T3510: RADIUS usersname is not shown on CLI, as Resolved.

May 2 2021, 4:31 PM · VyOS 1.4 Sagitta

c-po closed T3511: Update libnss-mapuser and libpam-radius packages from CUMULUS Linux as Resolved.

May 2 2021, 4:31 PM · VyOS 1.4 Sagitta

c-po added a comment to T3511: Update libnss-mapuser and libpam-radius packages from CUMULUS Linux.

https://github.com/vyos/libpam-radius-auth/commit/cf571ca6c722d3d2b0c359dddf835a3f406b194b
https://github.com/vyos/libnss-mapuser/commit/2ded63a0e6748018dada646691843462797cc7fc

May 2 2021, 4:31 PM · VyOS 1.4 Sagitta

syncer changed the edit policy for T141: TACACS+ Support.

May 2 2021, 4:14 PM · VyOS 1.4 Sagitta

syncer reassigned T141: TACACS+ Support from UnicronNL to c-po.

May 2 2021, 4:13 PM · VyOS 1.4 Sagitta

hard added a comment to T3480: Does not possible to change console baud-rate.

Checked on VM

vyos@vyos-dev# set system console device ttyS0 speed 115200
[edit]
vyos@vyos-dev# commit
[edit]
vyos@vyos-dev# show system console
 device ttyS0 {
     speed 115200
 }
[edit]

May 2 2021, 3:25 PM · VyOS 1.4 Sagitta

c-po updated the task description for T3510: RADIUS usersname is not shown on CLI.

May 2 2021, 11:15 AM · VyOS 1.4 Sagitta

c-po claimed T3510: RADIUS usersname is not shown on CLI.

May 2 2021, 10:38 AM · VyOS 1.4 Sagitta

c-po triaged T3511: Update libnss-mapuser and libpam-radius packages from CUMULUS Linux as Low priority.

May 2 2021, 10:38 AM · VyOS 1.4 Sagitta

c-po changed the status of T3511: Update libnss-mapuser and libpam-radius packages from CUMULUS Linux, a subtask of T3510: RADIUS usersname is not shown on CLI, from Open to In progress.

May 2 2021, 10:38 AM · VyOS 1.4 Sagitta

c-po changed the status of T3511: Update libnss-mapuser and libpam-radius packages from CUMULUS Linux from Open to In progress.

May 2 2021, 10:38 AM · VyOS 1.4 Sagitta

c-po created T3511: Update libnss-mapuser and libpam-radius packages from CUMULUS Linux.

May 2 2021, 10:38 AM · VyOS 1.4 Sagitta

c-po created T3510: RADIUS usersname is not shown on CLI.

May 2 2021, 10:38 AM · VyOS 1.4 Sagitta

May 1 2021

c-po closed T3379: Add global-parameters name-server for dhcpv6-server as Resolved.

May 1 2021, 7:28 AM · VyOS 1.3 Equuleus (1.3.0), VyOS 1.4 Sagitta

c-po moved T3379: Add global-parameters name-server for dhcpv6-server from Need Triage to Finished on the VyOS 1.3 Equuleus board.

May 1 2021, 7:28 AM · VyOS 1.3 Equuleus (1.3.0), VyOS 1.4 Sagitta

c-po moved T3489: NUMA has been disabled for the past few years and no-one has noticed from Open to Finished on the VyOS 1.4 Sagitta board.

May 1 2021, 7:26 AM · VyOS 1.4 Sagitta

c-po closed T3491: Change Kernel HZ to 1000 as Resolved.

May 1 2021, 7:26 AM · VyOS 1.3 Equuleus (1.3.0), VyOS 1.4 Sagitta

c-po claimed T3491: Change Kernel HZ to 1000.

May 1 2021, 7:25 AM · VyOS 1.3 Equuleus (1.3.0), VyOS 1.4 Sagitta

c-po moved T3484: Kernel panic when QAT uses from Open to Backlog on the VyOS 1.4 Sagitta board.

May 1 2021, 7:13 AM · VyOS 1.4 Sagitta

c-po moved T3479: route-maps containing "aggregator as" can not be deleted from Finished to Backlog on the VyOS 1.3 Equuleus board.

May 1 2021, 7:11 AM · VyOS 1.4 Sagitta

c-po moved T3479: route-maps containing "aggregator as" can not be deleted from Need Triage to Finished on the VyOS 1.3 Equuleus board.

May 1 2021, 7:11 AM · VyOS 1.4 Sagitta

Apr 30 2021

Viacheslav added a comment to T3461: OpenConnect Server redundancy check.

PR https://github.com/vyos/vyos-1x/pull/827

Apr 30 2021, 3:35 PM · VyOS 1.3 Equuleus (1.3.0), VyOS 1.4 Sagitta

c-po added a comment to T3504: BGP Per Peer Graceful Restart.

This requires a fix to https://github.com/FRRouting/frr/issues/8403 first

Apr 30 2021, 2:38 PM · VyOS 1.4 Sagitta

c-po changed the status of T3504: BGP Per Peer Graceful Restart from Open to In progress.

Apr 30 2021, 2:38 PM · VyOS 1.4 Sagitta

Viacheslav added a project to T1083: Implement persistent/random address and port mapping options for NAT rules: VyOS 1.4 Sagitta.

Apr 30 2021, 12:10 PM · VyOS 1.2 Crux (VyOS 1.2.9), VyOS 1.3 Equuleus (1.3.0), test, VyOS 1.4 Sagitta

c-po renamed T3318: Update Linux Kernel to v5.4.208 / 5.10.142 from Update Linux Kernel to v5.4.114 / 5.10.32 to Update Linux Kernel to v5.4.115 / 5.10.33.

Apr 30 2021, 4:12 AM · VyOS 1.3 Equuleus (1.3.2), VyOS 1.4 Sagitta

Apr 29 2021

stepler closed T3503: "route-reflector-client" fails when "remote-as" is "internal" as Resolved.

Looks good on 1.4-rolling-202104280417:

Apr 29 2021, 2:28 PM · VyOS 1.4 Sagitta

stepler closed T3502: "system ip multipath layer4-hashing" doesn't work as Resolved.

Looks good on 1.4-rolling-202104280417 and 1.3-rolling-202104280642:

Apr 29 2021, 2:28 PM · VyOS 1.3 Equuleus (1.3.0), VyOS 1.4 Sagitta

erkin added a subtask for T3356: Script for remote file transfers: T3506: Migrate loadkey command to op-mode.

Apr 29 2021, 2:28 PM · VyOS 1.3 Equuleus (1.3.0), VyOS 1.4 Sagitta

erkin added a parent task for T3506: Migrate loadkey command to op-mode: T3356: Script for remote file transfers.

Apr 29 2021, 2:28 PM · VyOS 1.4 Sagitta

erkin added a parent task for T3506: Migrate loadkey command to op-mode: T3355: Remove all remaining legacy Vyatta code.

Apr 29 2021, 2:17 PM · VyOS 1.4 Sagitta

erkin added a subtask for T3355: Remove all remaining legacy Vyatta code: T3506: Migrate loadkey command to op-mode.

Apr 29 2021, 2:17 PM · VyOS Rolling

erkin triaged T3506: Migrate loadkey command to op-mode as Low priority.

Apr 29 2021, 2:17 PM · VyOS 1.4 Sagitta

Viacheslav added a comment to T2845: BGP conf_mode unable to delete configuration with peer-group.

A possible reason it tried to remove " neighbor 10.0.0.2 remote-as 65002" after " neighbor 10.0.0.2 interface peer-group foo"
But if we delete " neighbor 10.0.0.2 interface peer-group foo" it also delete and "" neighbor 10.0.0.2 remote-as 65002"
So it can't delete this string

Apr 29 2021, 10:06 AM · VyOS 1.4 Sagitta

Viacheslav added a subtask for T3116: Support back-end L4 level load balancing: T3209: Load balancing rules in firewall.

Apr 29 2021, 8:37 AM · VyOS 1.4 Sagitta

Viacheslav added a comment to T3250: PPPoE server: wrong local usernames.

PR https://github.com/vyos/vyos-1x/pull/825

Apr 29 2021, 8:31 AM · VyOS 1.3 Equuleus (1.3.0), VyOS 1.4 Sagitta

Apr 28 2021

Viacheslav added a comment to T3217: Save FRR configuration on each commit.

PR's for Equuleus, save frr configurations.
https://github.com/vyos/vyatta-cfg/pull/39
https://github.com/vyos/vyatta-cfg-quagga/pull/75

Apr 28 2021, 9:24 PM · VyOS 1.3 Equuleus (1.3.0-epa1), VyOS 1.4 Sagitta

Viacheslav added a comment to T3333: "show vpn ipsec sa" reports ESP tunnels to be up when they are not..

For crux we use parser of " ipsec statusall {peer}"
Output if IKE established and esp SA not installed

vyos@r2-lts:~$ sudo ipsec statusall peer-192.0.2.1-tunnel-vti | grep Connections -A 50
Connections:
peer-192.0.2.1-tunnel-vti:  192.0.2.2...192.0.2.1  IKEv1
peer-192.0.2.1-tunnel-vti:   local:  [192.0.2.2] uses pre-shared key authentication
peer-192.0.2.1-tunnel-vti:   remote: [192.0.2.1] uses pre-shared key authentication
peer-192.0.2.1-tunnel-vti:   child:  0.0.0.0/0 === 0.0.0.0/0 TUNNEL
Security Associations (2 up, 0 connecting):
peer-192.0.2.1-tunnel-vti[3]: ESTABLISHED 12 minutes ago, 192.0.2.2[192.0.2.2]...192.0.2.1[192.0.2.1]
peer-192.0.2.1-tunnel-vti[3]: IKEv1 SPIs: 0ab8c2ee5815350e_i 271fba46aab245da_r*, pre-shared key reauthentication in 29 minutes
peer-192.0.2.1-tunnel-vti[3]: IKE proposal: AES_CBC_256/HMAC_SHA1_96/PRF_HMAC_SHA1/MODP_1024

Apr 28 2021, 3:04 PM · VyOS 1.2 Crux (VyOS 1.2.8)

zsdc changed the status of T3505: Commits do not respect changes in FRR that are not stored in a config from Open to Confirmed.

Apr 28 2021, 2:41 PM · VyOS 1.4 Sagitta (1.4.0-GA)

Viacheslav edited projects for T3333: "show vpn ipsec sa" reports ESP tunnels to be up when they are not., added: VyOS 1.2 Crux (VyOS 1.2.8); removed VyOS 1.2 Crux.

Apr 28 2021, 2:34 PM · VyOS 1.2 Crux (VyOS 1.2.8)

Viacheslav closed T3473: IPSec op-mode show sa error as Resolved.

Apr 28 2021, 2:16 PM · VyOS 1.4 Sagitta

Viacheslav claimed T3333: "show vpn ipsec sa" reports ESP tunnels to be up when they are not..

Apr 28 2021, 1:42 PM · VyOS 1.2 Crux (VyOS 1.2.8)

Viacheslav added a comment to T3333: "show vpn ipsec sa" reports ESP tunnels to be up when they are not..

PR for Equuleus https://github.com/vyos/vyos-1x/pull/823

Apr 28 2021, 1:42 PM · VyOS 1.2 Crux (VyOS 1.2.8)